相信很多消費者在向無錫環氧地坪廠家公司咨詢環氧地坪漆報價的時候，基本上會被問到基礎地面的情況如何，是否平整、存在起砂起灰現象，以及硬度如何等問題，這主要是因為，基礎地面的好壞直接影響無錫環氧地坪漆材料的用量，進而影響地坪漆最終報價。因此，環氧地坪漆廠家給客戶報價的時候需要對基礎地面進行診斷，主要有以下幾個方面：

It is believed that when many consumers consult the floor paint manufacturers for quotation, they will be basically asked about the situation of the floor paint, whether it is flat, whether there is sand and ash phenomenon, and how hard it is. This is mainly because the quality of the floor directly affects the amount of floor paint materials, and then affects the final quotation of floor paint. Therefore, the floor paint manufacturers need to diagnose the basic floor when quoting price to customers, mainly in the following aspects: 1、 首先確定地面種類：通常有普通混凝土、水磨石、耐磨地坪、環氧樹脂地坪等，不同的地坪基材會有不同的施工方案和工藝，其研磨、修補、固化等成本會有較大的差異;

1. Firstly, the types of floor are determined: there are usually ordinary concrete, terrazzo, wear-resistant floor, epoxy resin floor, etc. Different floor base materials will have different construction schemes and processes, and the cost of grinding, repairing and curing will be quite different.

2、 鑒定地面平整度：可用2米靠尺或目測的方式，查看平整度或地面波浪起伏程度等，也可用專業測評儀進行測定，一般平整度在3mm以內的則較為平整，平整度超過3mm的則會大幅增加研磨成本;

2. Appraisal of ground smoothness: It can be checked by 2-meter ruler or visual measurement to see the smoothness or the fluctuation of ground wave, etc. It can also be measured by professional measuring instrument. Generally, the smoothness is smoother within 3 mm, and the cost of grinding will be greatly increased if the smoothness exceeds 3 mm.

3、 鑒定地面硬度：可用專業莫氏硬度筆測定或用硬幣刮劃的方式測定，硬度好有利于研磨出較好的效果;

3. Appraisal of ground hardness: It can be measured by professional Mohs hardness pen or by coin scratching. Good hardness is conducive to better grinding effect.

4、 鑒定地面疏松度：主要測定起砂程度，最好的方法是用專用工具深挖至少1cm以上，看整個混凝土層的起砂程度，以便確定合理的環氧地坪漆施工工藝;

4. Appraisal of ground porosity: The best way to measure sand-blasting degree is to dig at least 1 cm deep with special tools to see the sand-blasting degree of the whole concrete layer, so as to determine the reasonable construction technology of epoxy floor paint.

5、 鑒定地面均勻一致性：地面的均勻一致性直接關乎固化拋光后的效果，簡單的辦法可用灑水法，觀察地面是否均勻一致。

5. Identify the uniformity of the ground: The uniformity of the ground is directly related to the effect of solidification and polishing. A simple method can be used to observe whether the ground is uniform or not by sprinkler method.

以上只是對需要施工環氧地坪地面一個簡單的診斷，具體的情況必須要通過勘查過地面情況后，才能制定準備的方案和報價，因此這也是為什么很多客戶在咨詢價格的時候一定要先看地面的原因。對基礎地面診斷之后，對地面處理的方法：

Above is only a simple diagnosis of the need to construct epoxy flooring ground, the specific situation must be through the survey of the ground conditions before the preparation of the plan and quotation, so this is why many customers in the consultation price must first look at the ground. After the diagnosis of the foundation ground, the methods of ground treatment are as follows:

1、初步掃清：用掃把將待處理地面上的垃圾清理干凈，有水的地方首先應該切斷水源，并清除表層積水，再設法使地面干燥;有油污的地方應用有機溶劑等(比如天那水，二甲苯等)洗凈，擦干，有油漆或其它不明污染物的地方應作適當處理，其方法用打磨，有機溶劑擦洗等。

1. Preliminary cleaning: Clean up the garbage on the ground to be treated with a broom. The water source should be cut off and the surface water should be removed before drying the ground. Wash and dry the oil-stained areas with organic solvents (such as Tiannashui, xylene, etc.) and the areas with paint or other unknown pollutants should be properly treated by polishing and organic solvents. Scrubbing and so on.

2、打磨：(針對水磨石基面或較光滑致密的水泥基面)，提供適當粗糙度。用吸塵打磨機全面打磨去除表面不易清掃的浮沉且打毛基面，以增強涂層與地面與地面的結合力，將待處理基面的高低不平處基本磨平，起找平作用。手磨機打磨對于大打磨機打不到的地方或打不掉之油污等可用手磨機打磨，注意應選用專用砂輪片。鋼絲刷處理，對于大打磨機和手磨機打不到的地方，或不必用手磨機打磨的區域，如生產線下面，可用砂紙打磨或用鋼絲刷處理等方法達到打磨效果。

2. Grinding: (for terrazzo base or smoother and denser cement base), provide appropriate roughness. In order to enhance the bond between the coating and the ground, a vacuum grinder is used to grind and remove the floating and sinking surface, which is not easy to clean, and to smooth the unevenness of the ground surface to be treated, so as to play a leveling role. Hand grinder grinding can be used for grinding where the big grinder can not grind or oil stain can not be removed. Special grinding wheels should be selected. Wire brush treatment, for large grinder and hand grinder can not be polished, or do not need to use hand grinder to polish areas, such as under the production line, can use sandpaper grinding or wire brush treatment methods to achieve grinding effect.

3、再次清掃，貼保護膠紙。徹底清理地面灰塵，對于不易清潔的衛生死角，可用吸塵器吸塵;將墻角，機腳，或其他應受保護的地方用膠帶紙包扎保護;按實際情況而定，是否需要再做一次清掃。

3. Clean up again and stick protective tape. Clean up the ground dust thoroughly. Vacuum cleaner can be used to clean the sanitary dead corner which is not easy to clean; tape the corner, foot or other places which should be protected to protect; according to the actual situation, whether it is necessary to do another cleaning.