有很多客戶給我們咨詢說自家別墅外有一段坡起路段可以鋪無震動止滑坡道材料嗎?小區內部的人行路鋪設無震動止滑坡道材料效果好嗎?我們的技術客服也會一一的細心回答客戶，可以做的，而且這些路段是很有必要鋪設無震動止滑坡道材料的。為了讓客戶們了解更多，我們來給大家介紹下無震動止滑坡道的適用范圍吧。無震動止滑坡道適用范圍: 道路路口、自行車道路、公交車道、汽車上下坡道、機場上下坡道、小區人行通道、斜坡、路面有特殊止滑要求的部位、美化區域等。
Many customers consulted us that there is a section of slope road outside their villas that can be paved with non-vibration anti-landslide material? Is it good to pave non-vibration anti-landslide material on the pedestrian road inside the community? Our technical customer service will answer customers one by one carefully and can do it, and these sections are very necessary to lay non-vibration anti-landslide material. In order to let customers know more, let's introduce the scope of application of non-vibration landslide. Scope of application of non-vibration landslide stopping road: road junction, bicycle road, bus lane, automobile up and down ramp, airport down and down ramp, residential pedestrian passage, slope, pavement with special anti-slip requirements, beautifying area, etc. 
無震動止滑坡道施工
Construction of Non-vibration Landslide Stopping Road

1、地面清潔：將混凝土基面進行清潔打磨，確保沒有油污、污泥、水泥塊屑和其他附著物，并對高低不平的地方進行找平處理，無空鼓并用水清洗。
1. Ground cleaning: Clean and polish the concrete base surface to ensure that there is no oil, sludge, cement debris and other attachments, and leveling the uneven areas, no empty drum and water cleaning.

2、界面層：使用無震動防滑車道液料加1倍的水?dāng)嚢杈鶆颍脻L筒或噴霧器均勻涂布于基層之上，形成界面層。
2, interface layer: use non vibration anti slip Lane liquid material plus 1 times of water mixing evenly, using roller or sprayer evenly coated on the base, forming interface layer.

3、底層施工：先用無震動防滑車道液料:無震動防滑車道粉料按1:5的比例配好攪拌均勻后并施工于界面層上(一般底層為黃色)。6小時后用噴霧器使用無震動防滑車道液料加1倍的水?dāng)嚢杈鶆?，用滾筒或噴霧器均勻涂布于基層之上，形成界面層。
3. Bottom layer construction: First use the non-vibration anti-skid Lane liquid material: non-vibration anti-skid Lane powder mixing uniformly according to the proportion of 1:5 and then constructed on the interface layer (generally the bottom is yellow). After 6 hours, use the sprayer to use the non vibration anti skid Lane material and add 1 times water to mix evenly. Use the roller or sprayer to spread evenly on the base, forming the interface layer.

4、粘貼分界線：按設計要求劃線，粘貼膠帶紙。常用色彩為黃色底層，綠色面層，黃底寬為了12公分，綠面寬為30公分，鈍角約為了150°左右。
4. Adhesion demarcation line: According to the design requirements, draw lines and paste tape paper. Commonly used color is yellow bottom, green surface, yellow bottom width is 12 cm, green surface width is 30 cm, obtuse angle is about 150 degrees.

5、面層施工：先用無震動防滑車道液料:無震動防滑車道粉料按1:5的比例配好攪拌均勻后并施工于底層上(一般面層為綠色)。
5. Surface layer construction: first use non-vibration anti-skid Lane liquid material: non-vibration anti-skid Lane powder mix well in proportion of 1:5 and then construct on the bottom (generally the surface is green).

6、清理現場：清理多余材料，使地面干凈無污染。
6. Clean up the site: Clean up excess materials to make the ground clean and pollution-free.

7、養護層：使用無震動防滑車道液料加一倍的水用噴霧器均勻涂布于產品表面以養護成品。
7, curing layer: use the non vibration anti-skid Lane liquid material and double water sprayer evenly coated on the product surface to maintain the finished product.