在環氧地坪漆行業有句話“三分材料、七分施工”，說的是在環氧地坪漆施工的時候，為了保證施工質量，我們必須了解和掌握環氧地坪漆施工工藝，只有這樣才能達到我們想要的施工效果。為了確保環氧地坪漆施工效果能夠達到我們的預期，在施工過程中需要做好以下幾點：

In the epoxy floor paint industry, there is a saying "three-component materials, seven-component construction". It means that in order to ensure the construction quality, we must understand and master the construction technology of epoxy floor paint, only in this way can we achieve the desired construction effect. In order to ensure that the construction effect of epoxy floor paint can meet our expectations, the following points need to be done well in the construction process: 

1、環氧地坪漆涂裝前基礎地面處理的質量控制

1. Quality Control of Foundation Ground Treatment before Epoxy Floor Paint Coating

應按被涂物件表面處理要求，采用科學有效的處理方法，徹底清除被涂物件表面的油垢、銹蝕及雜質，保證被涂物表面清潔、干燥。尤其是被涂物表面應有一定的粗糙度，對保證環氧地坪涂料涂裝質量起重要作用。

According to the requirements of surface treatment of coated objects, scientific and effective treatment methods should be adopted to thoroughly remove grease scale, rust and impurities on the surface of coated objects to ensure that the surface of coated objects is clean and dry. Especially the surface roughness of the coating should be certain, which plays an important role in guaranteeing the quality of epoxy floor coating.

2、施工過程中的質量控制

2. Quality Control in Construction

環氧地坪漆施工工藝要求非常嚴格，每道施工后，都應仔細觀測表面狀態，涂膜是否均勻、有無氣孔、粗粒、涂膜固化速度等。發現問題應及時解決。需一定按施工規定的每道涂裝厚度及固化條件嚴格操作，避免施工時產生質量事故。

The construction technology of epoxy floor paint is very strict. After each construction, we should carefully observe the surface condition, whether the film is uniform, whether there are air holes, coarse grains, curing speed of the film, etc. Problems should be solved in time when they are found. It is necessary to operate strictly according to the thickness of each coating and curing conditions stipulated in the construction, so as to avoid quality accidents during the construction.

3、最終質量檢測

3. Final Quality Inspection

環氧地坪材料施工程序全部結束后，應按質量標準規定對涂裝質量進行全面質量檢查。檢測涂膜的硬度、厚度、附著力、表面狀態、光澤等質量指標。發現涂膜有氣泡、裂痕、起皺和縮孔等弊病時，應采取有效的補救措施，否則不能達到防護目的。

After the construction procedure of floor materials has been completed, the painting quality shall be inspected in accordance with the quality standards. The hardness, thickness, adhesion, surface state and gloss of the coating were measured. Effective remedial measures should be taken when defects such as bubbles, cracks, wrinkles and shrinkage holes are found in the coating, otherwise the protective purpose can not be achieved.